Code
Used on
Indicates the Federal item name
c.
Description.
d e s c r i p t i o n required to identify the
and a minir.
TS-1836/V
AM7
i t e m . The last line indicates the reference number
f o l l o w e d by the applicable Federal Supply Code for
b. The following publications pertain to the TS-
M a n u f a c t u r e r (FSCM) in parentheses. The FSCM is
1836/U and its components:
u s e d as an element in item identification to desig-
nate manufacturer or distributor or Government
O p e r a t o r , Organizational,
TM 11-6625-539-15
agency, etc. and is identified in SB 708-42.
Field and Depot Main-
d. Unit of Measure (U/M). Indicates the standard
tenance Manual: Tran-
or basic quantity by which the listed item is used in
sistor Test Set TS-
performing the actual maintenance function. This
1836/U
measure
is
expressed
by
a
two-character
alpha-
O r g a n i z a t i o n a l Mainte-
TM
11-6625-539-20P
betical abbreviation; e.g., ea, in, pr, etc., and is the
nance Repair Parts and
b a s i s used to indicate quantities and allowances in
Special Tools Lists:
s u b s e q u e n t columns. When the unit of measure dif-
Test Set, Transistor
fers from the unit of issue, the lowest unit of issue
TS-1836/U
t h a t will satisfy the required units of measure will
be
requisitioned.
e. Quantity Incorporated in Unit. This column in-
d i c a t e s the quantity of the item used in the equip-
1-5. Location of Repair Parts
m e n t . Subsequent appearances of the same item in
a. This manual contains one cross-reference index
the same assembly are indicated by the letters
"REF"
the Federal stock number or reference number
f. 30-Day DS/GS Maintenance Allowances.
g ) m a n u f a c t u r e r ' s part number) is known. The first
NOTE
column in the index is prepared in numerical or al-
Allowances
in
GS
column
are
for
GS
main-
p h a n u m e r i c sequence is ascending order. The refer-
tenance only.
ence
numbers
(manufacturer's
part
numbers)
are
(1) The repair parts indicated by asterisk entries
l i s t e d immediately following the last listed Federal
in separate allowance columns for GS represent
s t o c k number in the index of Federal stock num-
t h o s e authorized for use at that category of main-
bers.
tenance to be requisitioned on an "as required"
b. W h e n t h e F e d e r a l s t o c k n u m b e r o r r e f e r e n c e
b a s i s , until stockage is based on demand in accord-
number is known, follow the procedures given in
ance with AR 710-2.
(1) and (2) below.
(2) Allowance quantities are indicated in the
(1) Refer to the index of Federal stock numbers
s p e c i a l tool lists section for special tools, TMDE,
(see IV) and locate the Federal stock number or ref-
and other support equipment.
e r e n c e number. The FSN and reference number are
g.
1-Year
Allowance
Per
100
Equipmants/Con-
c r o s s - r e f e r e n c e d to the applicable figure and item
tingency
Planning
Purposes.
Column
intentionally
number or reference designation.
left blank.
(2) Refer to th repair parts list (sec II) and lo-
h. Depot Maintenance Allowance Per 100 Equip-
cate the figure number (col 10a) and item number or
m a n t . This column indicates opposite the first ap-
reference designation (col 10b) as noted in the FSN
pearance of each item the total quantity authorized
index.
for depot maintenance of 100 equipments.
c. When the figure and item number or reference
i.
Illustation.
This
column
is
divided
as
follows:
d e s i g n a t i o n are known, scrutinize columns 10a and
(1) Figure number. Indicates the figure number
10b of the repair parts list (sec II) until the item is
o f the illustration on which the item is shown in
located.
TM
11-6625-539-15.
d. When the FSN, reference number, figure num-
(2) Item number. Indicates the item number or
ber, item number and reference designation are not
r e f e r e n c e designation used to reference the item in
k n o w n , scrutinize column 3 of the repair parts list
the illustration.
(S e C II), which is arranged in alphabetical order.
Special
Information
a. Usable on codes arc included in column 3. Un-
c o d e d items are applicable to all models. Identifi-
Abbreviations
c a t i o n of the usable on codes used in this publia-
Not applicable.
tion are--
