TM 11-6625-539-14-3
as required are identified by an asterisk in the
Explanation
Code
allowance column.
will not be stocked above DS and GS level or
returned to depot supply level.
g. IIlustrations.
(2) Maintenance code-indicates the lowest
(1) Figure number her. Indicates the figure
category of maintenance authorized to install the
number of the illustration in which the item is
listed item. The maintenance level codes are:
shown.
Explanation
Code
H - - - - - - - - - - General Support Maintenance
(2) Item number or reference designation.
D - - - - - - - - -Depot Maintenance
Indicates the reference designation used to iden-
(3) Recoverability code indicates whether
tify the item in the illustration.
unserviceable items should be returned for recov-
ery or salvage. Items not coded are expendable.
C-4. Location of Repair Parts
Recoverability codes are:
Explanation
Code
R--Repair parts and assemblies that are economically
a. This manual contains two cross-reference in-
repairable at DSU and GSU activities and nor-
dexes (see III and sec IV) to be used to locate a
mally are furnished by supply on an exchange
repair part when either the Federal stock num-
basis.
ber, reference number (manufacturer's part
S--Repair parts and assemblies which are economically
repairable at DSU and GSU activities and which
number), or reference designation is know. The
normally are furnished by supply on an exchange
first column in each index is prepared in numer-
basis. When items are determined by GSU to be
ical or alphanumeric sequence in ascending order.
uneconomically repairable, they will be evacuated
Where a Federal stock number is not listed, refer
to a depot for evaluation and analysis before final
to the reference number (manufacturer's part
disposition.
numbers) immediately following the last listed
T--High dollar value recoverable repair parts which
are subject to special handling and are issued on
Federal stock number.
an exchange basis. Such repair parts normally
b. When the Federal stock number is known,
are repaired or overhauled at depot maintenance
activities.
follow the procedures given in (1) and (2) below.
U--Repair parts specifically selected for salvage by
(1) Refer to the index of Federal stock num-
reclamation units because of precious metal con-
bers (see III ) and locate the Federal stock num-
tent, critical materials, or high dollar value re-
ber. The FSN is cross-referenced to the applica-
usable casings or castings.
ble figure and reference designation.
b. Federal Stock Number her. Indicates the Fed-
(2) When the reference designation is de-
eral stock number assigned to the item and will
termined, refer to the reference designation in-
be used for requisitioning purposes.
dex (sec IV). The reference designations are
listed in alphanumeric ascending order and are
C.
Description. Indicates the Federal item
cross-referenced to the page number on which
name and any additional description of the item
they appear in the repair parts list (see H). Re-
required. The index number has been included as
fer to the page number noted in the index and
part of the description to aid in the location of
locate the reference designation in the repair
"same as" items. A part number, or other refer-
parts list (col. 10b). If the description column in-
ence number, is followed by the applicable five-
dicates that it is a "SAME AS" item, locate the
digit Federal supply code for manufacturers in
first appearance of the item by the index num-
parentheses.
ber.
d. Unit of Measure (U/M). A two-character
c. When the reference designation is known,
alphabetic abbreviation indicating the amount
follow the procedures given in b(2) above.
or quantity of the item upon which the allow-
d. When neither the FSN reference number,
ances are based, e.g., ft, ea, pr, etc.
nor reference designation is known, identify the
p a r t in the illustration and follow directions
e. Quantity Incorporated in Unit. Indicates the
given in c above; or, scrutinize column 3 of the
quantity of the item used in the TS1836C/U.
repair parts list (sec II).
Subsequent appearances of the same item in the
s a m e assembly are indicated by the letters
C-5. Federal Supply Code for Manufacturers
"REF".
Manufacturer's name
code
03984-------- General Electric Co, Semiconductor Prod-
f . Allowances (30-Day GS Maintenance, 1
ucts Dept
Year Per Equipment (Contingency), and Depot
06540----------Amatom Electronic Hardware, Div of
MITE Corp
M a i n t e n a n c e ) . Items authorized for requisition
C-2
