C 2 TM 9-6625-1754-14
Explanation
Explanation
Code
Code
High dollar value recoverable repair parts which
T
A
Assemblies which are not procured, or stocked as
are subject to special handling and are issued on
such, but are made up of two or more units.
an exchange basis. Such repair parts normally
Such component units carry individual stock
are repaired or overhauled at depot main-
numbers and descriptions, are procured and
tenance activities.
stocked separately and can be assembled to
Repair parts specifically selected for salvage by
U
form the required assembly at indicated
reclamation units because of precious metal
maintenance categories.
content, critical materials, or high dollar value
Parts and assemblies which are not procured or
X
reuseble casings or castings.
stocked and the mortality of which normally is
below that of the applicable end item or com-
b. F e d e r a l S t o c k N u m b e r . I n d i c a t e s t h e
ponent. The failure of such part or assembly
F e d e r a l stock number assigned to the item and
should result in retirement of the end item from
w i l l be used for requisitioning purposes.
the supply system.
Repair parts which are not procured or stocked.
c. D e s c r i p t i o n . I n d i c a t e s t h e F e d e r a l i t e m
X1
The requirement for such items will be filled by
name and any additional description of the item
use of the next higher assembly or component.
r e q u i r e d . , The index number has been included
Repair parts which are not stocked. The indicated
X2
as part of the description to aid in the location of
maintenance category requiring such repair
"SAME AS" items. A part number or other
parts will attempt to obtain same through
cannibalization. Where such repair parts are not
r e f e r e n c e number is followed by the applicable
through
cannibalization,
obtainable
f i v e - d i g i t Federal supply code for manufactures
requirement will will be requisitioned, with ac-
in parentheses.
companying justification, through normal
d. Unit of Measure (U/M). A two character
supply channels.
alphabetic abbreviation indicating the amount or
Maior assemblies that are procured with PEMA
G
funds for initial issue only as exchange
quantity of the item upon which the allowances
assemblies at DSU and GSU level. These
are based, e.g., ft, ea, pr, etc.
assemblies will not be stocked above DS and GS
e. Q u a n t i t y I n c o r p o r a t e d in Unit. Indicates
level or returned to depot supply level.
the quantity of the item used in AN / USM-303
(2) Maintenance code indicates the lowest
and AN / USM-303A.
category of maintenance authorized to install the
f. 15-Day Organizational Maintenance
l i s t e d items. The maintenance level codes are:
Allowance.
Explanation
Code
(1) The allowance columns are divided into
Operator / Crew
C
f o u r subcolumns. Indicated in each subcolumn
Organizational Maintenance
O
opposite the first appearance of each item is the
Direct support maintenance
F
total quantity of items authorized for the number
H
General support maintenance
D
Depot maintenance
o f e q u i p m e n t s supported.
Subsequent ap-
pearances of the same item will have the letters
(3) R e c o v e r a b i l i t y c o d e i n d i c a t e s w h e t h e r
"REF" in the allowance columns. Items
unserviceable items should be returned for
authorized for use as required, but not for initial
recovery or salvage. Items not coded are ex-
s t o c k a g e , are identified with an asterisk in the
p e n d a b l e . Recoverability codes are:
a l l o w a n c e column.
Code
Explanation
(2) The quantitative allowance for
Repair parts and assemblies that are economically
R
o r g a n i z a t i o n a l level of maintenance represents
repairable at DSU and GSU activities and are
nortmally furnished by supply on an exchange
one initial prescribed load for a 15-day period for
basis.
the number of equipments supported. Units and
R e p a i r parts and assemblies which are
S
o r g a n i z a t i o n s authorized additional prescribed
economically repairable at DSU and GSU
loads will multiply the number of prescribed
activities and which normally are furnished by
loads authorized by the quantity of repair parts
supply on an exchange basis. When items are
determined by GSU to be uneconomically
r e f l e c t e d in the appropriate density column to
repairable, the y will be evacuated to a depot for
obtain the total quantity of repair parts
evaluation and analysis before final disposition.
authorized.
C-2
