used as an element in item identification to designate
TM 11-6625-537-15 Operator, Organizational
manufacturer or distributor or Government agency,
Field, and Depot
etc., and is identified in SB 70842.
Maintenance Manual:
d. Unit of Measure (U/M). Indicates the standard
Differential Voltmeter
or basic quantity by which the listed item is used in
ME-202/U.
performing the actual maintenance function. This
TM 11-6625-537-20P Organizational Maintenance
measure is expressed by a two-character alphabeti-
Repair Parts and Special
cal abbreviation; e.g., ea, in, pr, etc., and is the basis
Tools Lists: Voltmeter,
used to indicate quantities and allowances in
Electronic ME-202/U.
subsequent columns. When the unit of measure
1-5. Location of Repair Parts
differs from the unit of issue, the lowest unit of issue
that will satisfy the required units of measure will be
a. This manual contains one cross-reference index
requisitioned.
(see IV) to be used to locate a repair part when either
e. Quantity Incorporated in Unit. This column
the Federal stock number or reference number
indicates the quantity of the item used in the
(manufacturer's part number) is known. The first
equipment. Subsequent appearances of the same
column in the index is prepared in numerical or
item in the same assembly are indicated by the
alphanumeric sequence in ascending order. The
letters "REF".
reference numbers (manufacturer's part numbers)
f. 30-Day DS/GS Maintenance Allowances.
are listed immediately following the last listed
NOTE
Federal stock number in the index of Federal stock
Allowances in GS column are for GS
numbers.
maintenance only.
b. When the Federal stock number or reference
(1) The repair parts indicated by asterisk entries
number is known, follow the procedures given in (1)
in separate allowance columns for DS and GS
and (2) below.
represent those authorized for use at that category
(1) Refer to the index of Federal stock numbers
of maintenance to be requisitioned on an "as
(see IV) and locate the Federal stock number or
required" basis, until stockage is based on demand in
reference number. The FSN and reference number
accordance with AR 710-2.
are cross-referenced to the applicable figure and
(2) Allowance quantities are indicated in the
item number or reference designation.
special tool lists section for special tools, TMDE, and
(2) Refer to the repair parts list (see II) and locate
other support equipment.
the figure number (col 10a) and item number or
g. 1-year Allowances Per 100 Equipments/
reference designation (col 10b) as noted in the FSN
Contingency Planning Purposes. Column in-
index.
tentionally left blank
c. When the figure and item number or reference
h. Depot Maintenance Allowance Per 100 Equip
designation are known, scrutinize columns 10a and
ments. This column indicates opposite the first
10b of the repair parts list (see II) until the item is
appearance of each item the total quantity au-
located.
thorized for depot maintenance of 100 equipments.
d. When the FSN, reference number, figure
i. Illustation This column is divided as follows:
number, item number and reference designation are
(1) Figure number. Indicates the figure number
not known, scrutinize column 3 of the repair parts list
of the illustration on which the item is shown in TM
(see II), which is arranged in alphabetical order.
11-6625-537-15.
1-6. Abbreviations
(2) Item number. Indicates the item number or
Not applicable.
reference designation used to reference the item in
1-7. Reporting of Equipment publication
the illustration.
Improvements
1-4. Special Information
The reporting of errors, omissions, and recommenda-
a. Usable on codes are included in column 3.
tions for improving this publication by the individual
Uncoded items are applicable to all models. Identifi-
user is encouraged. Reports should be submitted on
cation of the usable on codes used in this publication
DA Form 2028 (Recommended Changes to Publica-
are --
tions) and forwarded direct to Commander, US Army
Used on
Code
ME-202/U
A9W
Electronics Command, ATTN: AMSEL-MA-TMDE,
Fort Monmouth, NJ., 07703.
b. The following publications pertain to the
ME-202/U and its components:
(Next printed page is 6)
4
